TP-LINK TL-SL5428E V3 Betriebsanweisung Seite 1

TL-SL5428E 24-Port 10/100Mbps + 4-Port Gigabit JetStream L2 Managed Switch REV2.0.0 1910011020

IX duplex...158 speed.

TL-SL5428E JetStream L2 Managed Switch CLI Guide 84 Chapter 13 ARP Inspection Commands ARP (Address Resolution Protocol) Detect function is to protec

TL-SL5428E JetStream L2 Managed Switch CLI Guide 85 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet /

TL-SL5428E JetStream L2 Managed Switch CLI Guide 86 ip arp inspection limit-rate Description The ip arp inspection limit-rate command is used to confi

TL-SL5428E JetStream L2 Managed Switch CLI Guide 87 Example Restore Fast Ethernet port 5 to the ARP transmit status: TL-SL5428E(config)#interface fast

TL-SL5428E JetStream L2 Managed Switch CLI Guide 88 TL-SL5428E(config)#show ip arp inspection interface fastEthernet 1/0/1 Display the configuration o

TL-SL5428E JetStream L2 Managed Switch CLI Guide 89 Chapter 14 IP Verify Source Commands IP Verify Source is to filter the IP packets based on the IP

TL-SL5428E JetStream L2 Managed Switch CLI Guide 90 show ip verify source Description The show ip verify source command is used to display the IP Veri

TL-SL5428E JetStream L2 Managed Switch CLI Guide 91 Chapter 15 DoS Defend Command DoS (Denial of Service) Attack is to occupy the network bandwidth m

TL-SL5428E JetStream L2 Managed Switch CLI Guide 92 Parameter ping-rate —— Specify the transmission rate of the Ping packets when the Defend Type Ping

TL-SL5428E JetStream L2 Managed Switch CLI Guide 93 ip dos-prevent type Description The ip dos-prevent type command is used to select the DoS Defend T

X loopback-detection interval...179 loopback-detection

TL-SL5428E JetStream L2 Managed Switch CLI Guide 94 ip dos-prevent detect Description The ip dos-prevent detect command is used to configure the detec

TL-SL5428E JetStream L2 Managed Switch CLI Guide 95 show ip dos-prevent Description The show ip dos-prevent command is used to display the DoS informa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 96 Chapter 16 IEEE 802.1X Commands IEEE 802.1X function is to provide an access control for LAN port

TL-SL5428E JetStream L2 Managed Switch CLI Guide 97 pap: IEEE 802.1X authentication system uses extensible authentication protocol (EAP) to exchange i

TL-SL5428E JetStream L2 Managed Switch CLI Guide 98 TL-SL5428E(config)#dot1x guest-vlan 5 dot1x quiet-period Description The dot1x quiet-period comman

TL-SL5428E JetStream L2 Managed Switch CLI Guide 99 Command Mode Global Configuration Mode Example Configure the quiet period as 100 seconds: TL-SL542

TL-SL5428E JetStream L2 Managed Switch CLI Guide 100 Syntax dot1x no dot1x Command Mode Interface Configuration Mode (interface fastEthernet / interfa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 101 dot1x port-control Description The dot1x port-control command is used to configure the Control M

TL-SL5428E JetStream L2 Managed Switch CLI Guide 102 Syntax dot1x port-method { mac-based | port-based } no dot1x port-method Parameter mac-based | po

TL-SL5428E JetStream L2 Managed Switch CLI Guide 103 auth-key keyvalue ——The shared password for the switch and the authentication servers to exchan

XI spanning-tree mode...202 spanning-tree m

TL-SL5428E JetStream L2 Managed Switch CLI Guide 104 TL-SL5428E(config)#radius server-account show dot1x global Description The show dot1x global comm

TL-SL5428E JetStream L2 Managed Switch CLI Guide 105 TL-SL5428E(config)#show dot1x interface show radius accounting Description The show radius accoun

TL-SL5428E JetStream L2 Managed Switch CLI Guide 106 Chapter 17 PPPoE Circuit-ID Insertion Commands The PPPoE Circuit-ID Insertion feature provides a

TL-SL5428E JetStream L2 Managed Switch CLI Guide 107 Syntax pppoe circuit-id no pppoe circuit-id Command Mode Interface Configuration Mode (interface

TL-SL5428E JetStream L2 Managed Switch CLI Guide 108 Example Configure the type of PPPoE Circuit-ID as “mac” for the Fast Ethernet port 1/0/1: TL-SL54

TL-SL5428E JetStream L2 Managed Switch CLI Guide 109 Example Display the configuration information of PPPoE Circuit-ID Insertion function of all Ether

TL-SL5428E JetStream L2 Managed Switch CLI Guide 110 Chapter 18 System Log Commands The log information will record the settings and operation of the

TL-SL5428E JetStream L2 Managed Switch CLI Guide 111 logging file flash Description The logging file flash command is used to configure the level and

TL-SL5428E JetStream L2 Managed Switch CLI Guide 112 Immediate—— The system log file in the buffer will be synchronized to the flash immediately. This

TL-SL5428E JetStream L2 Managed Switch CLI Guide 113 clear logging Description The clear logging command is used to clear the information in the log b

XII show ethernet-oam statistics ...227 show ethernet-oam

TL-SL5428E JetStream L2 Managed Switch CLI Guide 114 priority. Only the log with the same or smaller severity level value will be sent to the correspo

TL-SL5428E JetStream L2 Managed Switch CLI Guide 115 index ——The index of the log host whose configuration will be displayed. Display the configuratio

TL-SL5428E JetStream L2 Managed Switch CLI Guide 116 Syntax show logging flash [level level] Parameter level ——Severity level. There are 8 severity le

TL-SL5428E JetStream L2 Managed Switch CLI Guide 117 Chapter 19 SSH Commands SSH (Security Shell) can provide the unsecured remote management with se

TL-SL5428E JetStream L2 Managed Switch CLI Guide 118 Example Enable SSH v2: TL-SL5428E(config)#ip ssh version v2 ip ssh timeout Description The ip ssh

TL-SL5428E JetStream L2 Managed Switch CLI Guide 119 Command Mode Global Configuration Mode Example Specify the maximum number of the connections to t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 120 show ip ssh Description The show ip ssh command is used to display the global configuration of SS

TL-SL5428E JetStream L2 Managed Switch CLI Guide 121 Chapter 20 SSL Commands SSL（Secure Sockets Layer）, a security protocol, is to provide a secure

TL-SL5428E JetStream L2 Managed Switch CLI Guide 122 Parameter ssl-cert —— The name of the SSL certificate which is selected to download to the swit

TL-SL5428E JetStream L2 Managed Switch CLI Guide 123 Command Mode Global Configuration Mode Example Download an SSL key named ssl-key from TFTP server

XIII ipv6 mld snooping router-aging-time ...249 ipv6 mld snooping mem

TL-SL5428E JetStream L2 Managed Switch CLI Guide 124 Chapter 21 MAC Address Commands MAC address configuration can improve the network security by

TL-SL5428E JetStream L2 Managed Switch CLI Guide 125 TL-SL5428E(config)#no mac address-table static 00:02:58:4f:6c:23 mac address-table aging-time Des

TL-SL5428E JetStream L2 Managed Switch CLI Guide 126 vid —— The corresponding VLAN ID of the MAC address. It ranges from 1 to 4094. Command Mode Glo

TL-SL5428E JetStream L2 Managed Switch CLI Guide 127 influence of the aging time and can only be deleted manually too. However, the learned entries wi

TL-SL5428E JetStream L2 Managed Switch CLI Guide 128 show mac address-table aging-time Description The show mac address-table aging-time command is us

TL-SL5428E JetStream L2 Managed Switch CLI Guide 129 show mac address-table interface Description The show mac address-table interface command is us

TL-SL5428E JetStream L2 Managed Switch CLI Guide 130 Syntax show mac address-table address mac-addr Parameter mac-addr —— The specified MAC address.

TL-SL5428E JetStream L2 Managed Switch CLI Guide 131 Chapter 22 System Configuration Commands System Configuration Commands can be used to configure

TL-SL5428E JetStream L2 Managed Switch CLI Guide 132 UTC-12:00 —— TimeZone for International Date Line West. UTC-11:00 —— TimeZone for Coordinated

TL-SL5428E JetStream L2 Managed Switch CLI Guide 133 backup-ntp-server —— The IP address for the Secondary NTP Server. fetching-rate —— Specify

XIV snmp-server user ...269 snmp-server

TL-SL5428E JetStream L2 Managed Switch CLI Guide 134 system-time dst date Description The system-time dst date command is used to specify the DST conf

TL-SL5428E JetStream L2 Managed Switch CLI Guide 135 system-time dst recurring Description The system-time dst recurring command is used to specify

TL-SL5428E JetStream L2 Managed Switch CLI Guide 136 hostname Description The hostname command is used to configure the system name. To clear the syst

TL-SL5428E JetStream L2 Managed Switch CLI Guide 137 contact-info Description The contact-info command is used to configure the system contact informa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 138 ip address Description The ip address command is used to configure the system IP address, Subnet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 139 Example Enable the DHCP Client function when the management VLAN of the switch is VLAN1: TL-SL542

TL-SL5428E JetStream L2 Managed Switch CLI Guide 140 Example Reset the software of the switch: TL-SL5428E#reset reboot Description The reboot command

TL-SL5428E JetStream L2 Managed Switch CLI Guide 141 copy startup-config tftp Description The copy startup-config tftp command is used to backup the c

TL-SL5428E JetStream L2 Managed Switch CLI Guide 142 name —— Specify the name for the configuration file which would be downloaded. Command Mode Priv

TL-SL5428E JetStream L2 Managed Switch CLI Guide 143 Upgrade the switch system file named as firmware.bin via the TFTP server with the IP address fe80

XV cluster ndp...296 cluster

TL-SL5428E JetStream L2 Managed Switch CLI Guide 144 milliseconds. If there is not any response after 8 times’ Ping test, the connection between the s

TL-SL5428E JetStream L2 Managed Switch CLI Guide 145 loopback interface Description The loopback interface command is used to test whether the port is

TL-SL5428E JetStream L2 Managed Switch CLI Guide 146 show system-time dst Description The show system-time dst command is used to display the DST tim

TL-SL5428E JetStream L2 Managed Switch CLI Guide 147 Syntax show system-info Command Mode Privileged EXEC Mode and Any Configuration Mode Example Disp

TL-SL5428E JetStream L2 Managed Switch CLI Guide 148 Parameter port —— The number of the port which is selected for Cable test. Command Mode Privile

TL-SL5428E JetStream L2 Managed Switch CLI Guide 149 Chapter 23 IPv6 Address Configuration Commands The IPv6 address configuration commands are provi

TL-SL5428E JetStream L2 Managed Switch CLI Guide 150 configured ipv6 link-local address will be deleted when the autoconfigured ipv6 link-local addres

TL-SL5428E JetStream L2 Managed Switch CLI Guide 151 ipv6 address dhcp Description The ipv6 address dhcp command is used to enable the DHCPv6 Client f

TL-SL5428E JetStream L2 Managed Switch CLI Guide 152 TL-SL5428E(config)# interface vlan 1 TL-SL5428E(config-if)# ipv6 address ra ipv6 address eui-64 D

TL-SL5428E JetStream L2 Managed Switch CLI Guide 153 no ipv6 address ipv6-addr Parameter ipv6-addr —— Global IPv6 address with network prefix, for exa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 1 Preface This Guide is intended for network administrator to provide referenced information about CL

TL-SL5428E JetStream L2 Managed Switch CLI Guide 154 Chapter 24 Ethernet Configuration Commands Ethernet Configuration Commands can be used to config

TL-SL5428E JetStream L2 Managed Switch CLI Guide 155 User Guidelines Command in the Interface Range fastEthernet Mode is executed independently on a

TL-SL5428E JetStream L2 Managed Switch CLI Guide 156 Parameter port-list —— The list of Gigabit Ethernet ports. Command Mode Global Configuration

TL-SL5428E JetStream L2 Managed Switch CLI Guide 157 shutdown Description The shutdown command is used to disable an Ethernet port. To enable this por

TL-SL5428E JetStream L2 Managed Switch CLI Guide 158 media-type Description The media-type command is used to configure the media type of Combo port.

TL-SL5428E JetStream L2 Managed Switch CLI Guide 159 TL-SL5428E(config)#interface gigabitEthernet 1/0/25 TL-SL5428E(config-if)#duplex full speed Descr

TL-SL5428E JetStream L2 Managed Switch CLI Guide 160 Parameter rate —— Specify the bandwidth for receiving broadcast packets on the port. The packet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 161 TL-SL5428E(config-if)#storm-control multicast storm-control unicast Description The storm-control

TL-SL5428E JetStream L2 Managed Switch CLI Guide 162 no bandwidth { all | ingress | egress } Parameter ingress-rate ——Specify the bandwidth for rece

TL-SL5428E JetStream L2 Managed Switch CLI Guide 163 Syntax show interface [fastEthernet port | gigabitEthernet port] status Parameter port ——The Fa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 2 Chapter 12: Binding Table Commands Provide information about the commands used for binding the IP a

TL-SL5428E JetStream L2 Managed Switch CLI Guide 164 show interface description Description The show interface description command is used to display

TL-SL5428E JetStream L2 Managed Switch CLI Guide 165 show interface configuration Description The show interface configuration command is used to dis

TL-SL5428E JetStream L2 Managed Switch CLI Guide 166 TL-SL5428E(config)#show storm-control interface range fastEthernet 1/0/4-7 show bandwidth Descrip

TL-SL5428E JetStream L2 Managed Switch CLI Guide 167 Chapter 25 QoS Commands QoS (Quality of Service) function is used to optimize the network perfor

TL-SL5428E JetStream L2 Managed Switch CLI Guide 168 Syntax qos cos no qos cos Command Mode Global Configuration Mode User Guidelines IEEE 802.1P give

TL-SL5428E JetStream L2 Managed Switch CLI Guide 169 qos queue cos-map Description The qos queue cos-map command is used to configure the mapping rela

TL-SL5428E JetStream L2 Managed Switch CLI Guide 170 divide IP datagram into 64 priorities. When DSCP Priority is enabled, IP datagram are mapped to d

TL-SL5428E JetStream L2 Managed Switch CLI Guide 171 queues and scheduling algorithms you set. On this switch, the priority levels are labeled as TC0,

TL-SL5428E JetStream L2 Managed Switch CLI Guide 172 Syntax show qos interface [ fastEthernet port | gigabitEthernet port | range fastEthernet po

TL-SL5428E JetStream L2 Managed Switch CLI Guide 173 Syntax show qos dscp-map Command Mode Privileged EXEC Mode and Any Configuration Mode Example Dis

TL-SL5428E JetStream L2 Managed Switch CLI Guide 3 Chapter 24: Ethernet Configuration Commands Provide information about the commands used for configu

TL-SL5428E JetStream L2 Managed Switch CLI Guide 174 Chapter 26 Port Mirror Commands Port Mirror refers to the process of forwarding copies of packet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 175 monitor session source interface Description The monitor session source interface command is u

TL-SL5428E JetStream L2 Managed Switch CLI Guide 176 TL-SL5428E(config)#monitor session 1 source interface fastEthernet 1/0/4-5,1/0/7 rx Delete the Fa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 177 Chapter 27 Port isolation Commands Port Isolation provides a method of restricting traffic flow

TL-SL5428E JetStream L2 Managed Switch CLI Guide 178 show port isolation Description The show port isolation command is used to display the forward po

TL-SL5428E JetStream L2 Managed Switch CLI Guide 179 Chapter 28 Loopback Detection Commands With loopback detection feature enabled, the switch can d

TL-SL5428E JetStream L2 Managed Switch CLI Guide 180 Example Specify the interval-time as 50 seconds: TL-SL5428E(config)#loopback-detection interval 5

TL-SL5428E JetStream L2 Managed Switch CLI Guide 181 Example Enable the loopback detection function of Gigabit Ethernet ports 25-27: TL-SL5428E(config

TL-SL5428E JetStream L2 Managed Switch CLI Guide 182 loopback-detection recover Description The loopback-detection recover command is used to remove t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 183 show loopback-detection interface Description The show loopback-detection interface command is u

I COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Othe

TL-SL5428E JetStream L2 Managed Switch CLI Guide 4 Chapter 37: Cluster Commands Provide information about the commands used for configuring the Cluste

TL-SL5428E JetStream L2 Managed Switch CLI Guide 184 Chapter 29 ACL Commands ACL (Access Control List) is used to filter data packets by configuring

TL-SL5428E JetStream L2 Managed Switch CLI Guide 185 no absolute Parameter start-date —— The start date in Absolute Mode, in the format of MM/DD/YYY

TL-SL5428E JetStream L2 Managed Switch CLI Guide 186 TL-SL5428E(config)#time-range tSeg1 TL-SL5428E(config-time-range)#periodic week-date off-day time

TL-SL5428E JetStream L2 Managed Switch CLI Guide 187 Command Mode Global Configuration Mode Example Define National Day, configuring the start date as

TL-SL5428E JetStream L2 Managed Switch CLI Guide 188 Parameter access-list-num —— ACL ID, ranging from 0 to 99. Command Mode Global Configuration

TL-SL5428E JetStream L2 Managed Switch CLI Guide 189 frag —— Enable/Disable Fragment. By default, it is disabled. If Fragment is enabled, this rule w

TL-SL5428E JetStream L2 Managed Switch CLI Guide 190 destination-ip —— The destination IP address contained in the rule. destination-ip-mask —— Th

TL-SL5428E JetStream L2 Managed Switch CLI Guide 191 Syntax rule rule-id {deny | permit} [ [smac source-mac] smask source-mac-mask ] [ [dmac destinati

TL-SL5428E JetStream L2 Managed Switch CLI Guide 192 access-list policy name Description The access-list policy name command is used to add Policy. T

TL-SL5428E JetStream L2 Managed Switch CLI Guide 193 Command Mode Global Configuration Mode Example Add ACL whose ID is 120 to policy1 and create an a

TL-SL5428E JetStream L2 Managed Switch CLI Guide 5 Chapter 1 Using the CLI 1.1 Accessing the CLI You can log on to the switch and access the CLI by

TL-SL5428E JetStream L2 Managed Switch CLI Guide 194 Parameter vlan-id —— The VLAN ID of Redirect. The data packets matching the corresponding ACL wi

TL-SL5428E JetStream L2 Managed Switch CLI Guide 195 s-mirror Description The s-mirror command is used to configure Stream Mirror function of policy a

TL-SL5428E JetStream L2 Managed Switch CLI Guide 196 Example Edit the actions for policy1. For the data packets matching ACL 120, specify the DSCP reg

TL-SL5428E JetStream L2 Managed Switch CLI Guide 197 Command Mode Interface VLAN Mode Example Bind policy1 to VLAN 2: TL-SL5428E(config)#interface vla

TL-SL5428E JetStream L2 Managed Switch CLI Guide 198 show access-list Description The show access-list command is used to display configuration of ACL

TL-SL5428E JetStream L2 Managed Switch CLI Guide 199 Syntax show access-list bind Command Mode Privileged EXEC Mode and Any Configuration Mode Example

TL-SL5428E JetStream L2 Managed Switch CLI Guide 200 Chapter 30 MSTP Commands MSTP (Multiple Spanning Tree Protocol), compatible with both STP and RS

TL-SL5428E JetStream L2 Managed Switch CLI Guide 201 TL-SL5428E(config)#interface fastEthernet 1/0/2 TL-SL5428E(config-if)#spanning-tree spanning-tree

TL-SL5428E JetStream L2 Managed Switch CLI Guide 202 designated port, they can transit their states to forwarding rapidly to reduce the unnecessary fo

TL-SL5428E JetStream L2 Managed Switch CLI Guide 203 spanning-tree mst configuration Description The spanning-tree mst configuration command is used

TL-SL5428E JetStream L2 Managed Switch CLI Guide 6 Figure 1-2 Connection Description 4. Select the port to connect in Figure 1-3, and click OK. Fig

TL-SL5428E JetStream L2 Managed Switch CLI Guide 204 Example Map the VLANs 1-100 to Instance 1: TL-SL5428E(config)#spanning-tree mst configuration TL-

TL-SL5428E JetStream L2 Managed Switch CLI Guide 205 Parameters revision —— The revision level for MST region identification, ranging from 0 to 6553

TL-SL5428E JetStream L2 Managed Switch CLI Guide 206 spanning-tree mst Description The spanning-tree mst command is used to configure MST Instance Por

TL-SL5428E JetStream L2 Managed Switch CLI Guide 207 Syntax spanning-tree priority pri no spanning-tree priority Parameter pri —— Bridge priority,

TL-SL5428E JetStream L2 Managed Switch CLI Guide 208 spanning-tree timer Description The spanning-tree timer command is used to configure forward-tim

TL-SL5428E JetStream L2 Managed Switch CLI Guide 209 Syntax spanning-tree hold-count value no spanning-tree hold-count Parameter value —— The maximu

TL-SL5428E JetStream L2 Managed Switch CLI Guide 210 spanning-tree bpdufilter Description The spanning-tree bpdufilter command is used to enable the

TL-SL5428E JetStream L2 Managed Switch CLI Guide 211 TL-SL5428E(config)#interface fastEthernet 1/0/2 TL-SL5428E(config-if)#spanning-tree bpduguard spa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 212 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 213 Syntax spanning-tree mcheck Command Mode Interface Configuration Mode (interface fastEthernet / i

TL-SL5428E JetStream L2 Managed Switch CLI Guide 7 6. The DOS prompt” TL-SL5428E>” will appear after pressing the Enter button as Figure 1-5 shown

TL-SL5428E JetStream L2 Managed Switch CLI Guide 214 Example Display the bridge parameters: TL-SL5428E(config)#show spanning-tree bridge show spanning

TL-SL5428E JetStream L2 Managed Switch CLI Guide 215 Parameter port —— The Fast/Gigabit Ethernet port number. Command Mode Privileged EXEC Mode and

TL-SL5428E JetStream L2 Managed Switch CLI Guide 216 Display all the ports information of MST Instance 1: TL-SL5428E(config)#show spanning-tree mst in

TL-SL5428E JetStream L2 Managed Switch CLI Guide 217 Chapter 31 Ethernet OAM Commands Ethernet OAM (standing for Operation, Administration, and Maint

TL-SL5428E JetStream L2 Managed Switch CLI Guide 218 Syntax ethernet-oam mode { passive | active } no ethernet-oam mode Parameter passive —— Specify t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 219 notify —— Enable/Disable the event notification. By default, it is enabled. threshold | window |

TL-SL5428E JetStream L2 Managed Switch CLI Guide 220 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 221 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 222 Example For error frame seconds event, configure the error threshold as 8 and the event detection

TL-SL5428E JetStream L2 Managed Switch CLI Guide 223 TL-SL5428E(config-if)# ethernet-oam remote-failure dying-gasp notify disable ethernet-oam remote-

TL-SL5428E JetStream L2 Managed Switch CLI Guide 8 Login Mode: It doesn’t require username and password, but a connection password is required. Note:

TL-SL5428E JetStream L2 Managed Switch CLI Guide 224 ethernet-oam remote-loopback Description The ethernet-oam remote-loopback command is used to requ

TL-SL5428E JetStream L2 Managed Switch CLI Guide 225 Parameter port —— The Fast/Gigabit Ethernet port number. By default, the Ethernet OAM statistics

TL-SL5428E JetStream L2 Managed Switch CLI Guide 226 show ethernet-oam configuration Description The show ethernet-oam configuration command is used t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 227 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display Ethernet OAM event l

TL-SL5428E JetStream L2 Managed Switch CLI Guide 228 Syntax show ethernet-oam status [ interface { fastEthernet | gigabitEthernet } port ] Parameter

TL-SL5428E JetStream L2 Managed Switch CLI Guide 229 Chapter 32 DLDP Commands DLDP (Device Link Detection Protocol) is used to monitor the link state

TL-SL5428E JetStream L2 Managed Switch CLI Guide 230 Example Specify the interval of sending advertisement packets as 10 seconds: TL-SL5428E(config)#

TL-SL5428E JetStream L2 Managed Switch CLI Guide 231 Example Reset the DLDP function globally: TL-SL5428E(config)# dldp reset dldp(interface) Descrip

TL-SL5428E JetStream L2 Managed Switch CLI Guide 232 TL-SL5428E (config)# interface range fastEthernet 1/0/2-4 TL-SL5428E (config-if-range)# dldp rese

TL-SL5428E JetStream L2 Managed Switch CLI Guide 233 Display the configuration and state of port 5: TL-SL5428E# show dldp interface fastEthernet 1/0/5

TL-SL5428E JetStream L2 Managed Switch CLI Guide 9 For example, the host’s global address is 3001::12/64（and its corresponding interface is 4 as showe

TL-SL5428E JetStream L2 Managed Switch CLI Guide 234 Chapter 33 IGMP Snooping Commands IGMP Snooping (Internet Group Management Protocol Snooping) is

TL-SL5428E JetStream L2 Managed Switch CLI Guide 235 Example Enable IGMP Snooping function of Gigabit Ethernet port 25: TL-SL5428E(config)#interface g

TL-SL5428E JetStream L2 Managed Switch CLI Guide 236 Example Specify the operation of processing unknown multicast as “discard”: TL-SL5428E(config)#ip

TL-SL5428E JetStream L2 Managed Switch CLI Guide 237 the format of 1/0/2; Gigabit Ethernet port, ranging from 1-4, in the format of 1/0/2. vlan-id —

TL-SL5428E JetStream L2 Managed Switch CLI Guide 238 leave-time —— Leave Time, which is the interval between the switch receiving a leave message from

TL-SL5428E JetStream L2 Managed Switch CLI Guide 239 ip igmp snooping filter(global) Description The ip igmp snooping filter command is used to add or

TL-SL5428E JetStream L2 Managed Switch CLI Guide 240 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet

TL-SL5428E JetStream L2 Managed Switch CLI Guide 241 Parameter mode —— Action Mode, with “refuse” and “accept” options. “Refuse” indicates only the

TL-SL5428E JetStream L2 Managed Switch CLI Guide 242 ip igmp snooping querier vlan (general query) Description The ip igmp snooping querier vlan comm

TL-SL5428E JetStream L2 Managed Switch CLI Guide 243 ip igmp snooping querier vlan (specific query) Description The ip igmp snooping querier vlan com

TL-SL5428E JetStream L2 Managed Switch CLI Guide 10 2. Type the default user name and password admin/admin, then press the Enter button to enter th

TL-SL5428E JetStream L2 Managed Switch CLI Guide 244 show ip igmp snooping Description The show ip igmp snooping command is used to display the globa

TL-SL5428E JetStream L2 Managed Switch CLI Guide 245 Display the IGMP filter configuration of Fast Ethernet ports 2-4: TL-SL5428E#show ip igmp snoopin

TL-SL5428E JetStream L2 Managed Switch CLI Guide 246 show ip igmp snooping groups Description The show ip igmp snooping groups command is used to dis

TL-SL5428E JetStream L2 Managed Switch CLI Guide 247 Syntax show ip igmp snooping filter [filter-addr-id-list] Parameter filter-addr-id-list ——The mul

TL-SL5428E JetStream L2 Managed Switch CLI Guide 248 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the configurations o

TL-SL5428E JetStream L2 Managed Switch CLI Guide 249 Chapter 34 MLD Snooping Commands MLD Snooping (Multicast Listener Discovery Snooping) is a multi

TL-SL5428E JetStream L2 Managed Switch CLI Guide 250 Example Specify MLD Snooping router port aging time as 100 seconds globally: TL-SL5428E(config)#

TL-SL5428E JetStream L2 Managed Switch CLI Guide 251 TL-SL5428E(config)# no ipv6 mld snooping report-suppression ipv6 mld snooping unknown-filter Desc

TL-SL5428E JetStream L2 Managed Switch CLI Guide 252 ipv6 mld snooping last-listener query-count Description The ipv6 mld snooping last-listener query

TL-SL5428E JetStream L2 Managed Switch CLI Guide 253 ipv6 mld snooping multicast-vlan vlan-id Description The ipv6 mld snooping multicast-vlan vlan-i

TL-SL5428E JetStream L2 Managed Switch CLI Guide 11 Figure 1-11 Enter into the Privileged EXEC Mode  Login Mode Firstly configure the Telnet login

TL-SL5428E JetStream L2 Managed Switch CLI Guide 254 ipv6 mld snooping vlan router-aging-time Description The ipv6 mld snooping vlan router-aging-time

TL-SL5428E JetStream L2 Managed Switch CLI Guide 255 Example Specify the member port aging time as 100 seconds in VLAN 2: TL-SL5428E(config)# ipv6 mld

TL-SL5428E JetStream L2 Managed Switch CLI Guide 256 Command Mode Global Configuration Mode Example Configure the gigabitEthernet 1/0/2 as static rout

TL-SL5428E JetStream L2 Managed Switch CLI Guide 257 Syntax ipv6 mld snooping querier vlan vlan-id no ipv6 mld snooping querier vlan vlan-id Parameter

TL-SL5428E JetStream L2 Managed Switch CLI Guide 258 ipv6 mld snooping querier vlan query-interval Description The ipv6 mld snooping querier vlan quer

TL-SL5428E JetStream L2 Managed Switch CLI Guide 259 Example Specify the source address which sends the Query message as fe80::1234 on VLAN 2: TL-SL54

TL-SL5428E JetStream L2 Managed Switch CLI Guide 260 Interface Configuration Mode Example Enable filter function on interface gigabitEthernet 1/0/2: T

TL-SL5428E JetStream L2 Managed Switch CLI Guide 261 Parameter filter-list —— Specify the filter id list, in format of 1,3,10. Command Mode Interface

TL-SL5428E JetStream L2 Managed Switch CLI Guide 262 Syntax clear ipv6 mld snooping statistics Command Mode Privileged EXEC Mode and Any Configuration

TL-SL5428E JetStream L2 Managed Switch CLI Guide 263 Example Display all of the VLAN information: TL-SL5428E(config)# show ipv6 mld snooping vlan show

TL-SL5428E JetStream L2 Managed Switch CLI Guide 12 Figure 1-13 Connecting to the switch 2. You are prompted to enter the connection password 456 yo

TL-SL5428E JetStream L2 Managed Switch CLI Guide 264 show ipv6 mld snooping filter Description The show ipv6 mld snooping filter command is used to d

TL-SL5428E JetStream L2 Managed Switch CLI Guide 265 Syntax show ipv6 mld snooping interface filter [gigabitEthernet port] Parameter port —— Specify t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 266 Parameter port —— Specify the port number. Command Mode Privileged EXEC Mode and Any Configuratio

TL-SL5428E JetStream L2 Managed Switch CLI Guide 267 Chapter 35 SNMP Commands SNMP (Simple Network Management Protocol) functions are used to manage

TL-SL5428E JetStream L2 Managed Switch CLI Guide 268 Parameter name —— The entry name of View, ranging from 1 to 16 characters. Each View can include

TL-SL5428E JetStream L2 Managed Switch CLI Guide 269 smode —— Security Model, with v1、v2c and v3 options. They represent SNMP v1, SNMP v2c and SNMP v

TL-SL5428E JetStream L2 Managed Switch CLI Guide 270 Syntax snmp-server user name { local | remote } group-name [smode { v1 | v2c | v3 }] [slev { noAu

TL-SL5428E JetStream L2 Managed Switch CLI Guide 271 Example Add Local User admin to Group group2, and configure the Security Model of the user as v3,

TL-SL5428E JetStream L2 Managed Switch CLI Guide 272 snmp-server host Description The snmp-server host command is used to add Notification. To delete

TL-SL5428E JetStream L2 Managed Switch CLI Guide 273 timeout —— The maximum time for the switch to wait for the response from the management station

TL-SL5428E JetStream L2 Managed Switch CLI Guide 13 Figure 1-15 Enter into the Privileged EXEC Mode Now you can manage your switch with CLI commands

TL-SL5428E JetStream L2 Managed Switch CLI Guide 274 Example Specify the local engineID as 1234567890, and the remote engineID as abcdef123456: TL-SL5

TL-SL5428E JetStream L2 Managed Switch CLI Guide 275 Example Enable the linkup trap for the switch: TL-SL5428E(config)# snmp-server traps snmp linkup

TL-SL5428E JetStream L2 Managed Switch CLI Guide 276 Example Enable the dhcp-filter trap for the switch: TL-SL5428E(config)# snmp-server traps securit

TL-SL5428E JetStream L2 Managed Switch CLI Guide 277 Parameter bandwidth-control —— Enable bandwidth-control trap. It is sent when the rate limit func

TL-SL5428E JetStream L2 Managed Switch CLI Guide 278 Note: The snmp-server traps mac command without any parameter is used to enable all the four ty

TL-SL5428E JetStream L2 Managed Switch CLI Guide 279 Note: The snmp-server traps vlan command without any parameter is used to enable the both traps

TL-SL5428E JetStream L2 Managed Switch CLI Guide 280 Parameter index —— The index number of the entry, ranging from 1 to 12, in the format of 1-3,5.

TL-SL5428E JetStream L2 Managed Switch CLI Guide 281 type —— The event type, with “none”, “log”, “notify” and “both” options. “None” indicates no pr

TL-SL5428E JetStream L2 Managed Switch CLI Guide 282 port ——String for the port on which the Alarm entry acts, format as module/slot/port, for exampl

TL-SL5428E JetStream L2 Managed Switch CLI Guide 283 TL-SL5428E(config)#rmon alarm 1-3 interface fastEthernet 1/0/2 owner owner1 interval 100 show snm

II CONTENTS Preface ………………………………………………………………………………….1 Chapter 1 Using the CLI ...

TL-SL5428E JetStream L2 Managed Switch CLI Guide 14 Figure 1-16 Enable SSH function  Password Authentication Mode 1. Open the software to log on t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 284 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the Group table: TL-

TL-SL5428E JetStream L2 Managed Switch CLI Guide 285 show snmp-server host Description The show snmp-server host command is used to display the Host t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 286 Parameter index —— The index number of the entry selected to display the configuration, ranging

TL-SL5428E JetStream L2 Managed Switch CLI Guide 287 Syntax show rmon alarm [index] Parameter index —— The index number of the entry selected to dis

TL-SL5428E JetStream L2 Managed Switch CLI Guide 288 Chapter 36 LLDP Commands LLDP function enables network devices to advertise their own device inf

TL-SL5428E JetStream L2 Managed Switch CLI Guide 289 Parameter multiplier —— Configure the Hold Multiplier parameter. It ranges from 2 to 10. By def

TL-SL5428E JetStream L2 Managed Switch CLI Guide 290 is, the transmit interval will be shorten to a second, and several LLDPDUs will be sent out (the

TL-SL5428E JetStream L2 Managed Switch CLI Guide 291 Syntax lldp transmit no lldp transmit Command Mode Interface Configuration Mode (interface fastEt

TL-SL5428E JetStream L2 Managed Switch CLI Guide 292 lldp tlv-select Description The lldp tlv-select command is used to configure TLVs to be included

TL-SL5428E JetStream L2 Managed Switch CLI Guide 293 TL-SL5428E#show lldp show lldp interface Description The show lldp interface command is used to

TL-SL5428E JetStream L2 Managed Switch CLI Guide 15 Figure 1-18 Log on the Switch  Key Authentication Mode 1. Select the key type and key length,

TL-SL5428E JetStream L2 Managed Switch CLI Guide 294 Example Display the LLDP information of Fast Ethernet port 1: TL-SL5428E#show lldp local-informat

TL-SL5428E JetStream L2 Managed Switch CLI Guide 295 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the LLDP statistic i

TL-SL5428E JetStream L2 Managed Switch CLI Guide 296 Chapter 37 Cluster Commands Cluster Management function enables a network administrator to manag

TL-SL5428E JetStream L2 Managed Switch CLI Guide 297 TL-SL5428E(config)#cluster ndp TL-SL5428E(config)#cluster ndp timer hello 50 aging 120 cluster

TL-SL5428E JetStream L2 Managed Switch CLI Guide 298 Example Enable NTDP function globally, and specify NTDP Hops as 5, NTDP Interval Time as 30 minut

TL-SL5428E JetStream L2 Managed Switch CLI Guide 299 Example Enable NDP and NTDP function for Fast Ethernet port 5: TL-SL5428E(config)#interface fastE

TL-SL5428E JetStream L2 Managed Switch CLI Guide 300 Command Mode Global Configuration Mode Example Configure the newly created cluster name as tp:

TL-SL5428E JetStream L2 Managed Switch CLI Guide 301 Syntax cluster member {mac-address mac-address} no cluster member {mac-address mac-address} Param

TL-SL5428E JetStream L2 Managed Switch CLI Guide 302 Example Specify the current switch as individual switch: TL-SL5428E(config)#cluster individual sh

TL-SL5428E JetStream L2 Managed Switch CLI Guide 303 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the global informati

TL-SL5428E JetStream L2 Managed Switch CLI Guide 16 Figure 1-20 Save the Generated Key 3. Log on to the switch by the console port, and download the

TL-SL5428E JetStream L2 Managed Switch CLI Guide 304 Example Display the member information: TL-SL5428E#show cluster member show cluster manage role D

TL-SL5428E JetStream L2 Managed Switch CLI Guide 17 Figure 1-22 SSH Connection Config 5. Click Browse to load the private key file to SSH client soft

TL-SL5428E JetStream L2 Managed Switch CLI Guide 18 Figure 1-24 Log on the Switch 1.2 CLI Command Modes The CLI is divided into different command mo

TL-SL5428E JetStream L2 Managed Switch CLI Guide 19 Mode Accessing Path Prompt Logout or Access the next modeGlobal Configuration Mode Use the conf

TL-SL5428E JetStream L2 Managed Switch CLI Guide 20 e). Interface vlan: Configure parameters for the vlan-port.  Vlan Configuration Mode: In this m

TL-SL5428E JetStream L2 Managed Switch CLI Guide 21  Bold indicates an unalterable keyword. For example: show logging  Normal Font indicates a con

TL-SL5428E JetStream L2 Managed Switch CLI Guide 22 Chapter 2 User Interface enable Description The enable command is used to access Privileged EXEC

TL-SL5428E JetStream L2 Managed Switch CLI Guide 23 TL-SL5428E(config)#enable password admin disable Description The disable command is used to retur

III show vlan ...32 Chapte

TL-SL5428E JetStream L2 Managed Switch CLI Guide 24 exit Description The exit command is used to return to the previous Mode from the current Mode.

TL-SL5428E JetStream L2 Managed Switch CLI Guide 25 show history Description The show history command is used to show the latest 20 commands you ente

TL-SL5428E JetStream L2 Managed Switch CLI Guide 26 Chapter 3 IEEE 802.1Q VLAN Commands VLAN (Virtual Local Area Network) technology is developed for

TL-SL5428E JetStream L2 Managed Switch CLI Guide 27 interface vlan Description The interface vlan command is used to create VLAN Interface hereafter t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 28 Example Specify the description string of the VLAN 2 as “VLAN002”: TL-SL5428E(config)#vlan 2 TL-SL

TL-SL5428E JetStream L2 Managed Switch CLI Guide 29 Parameter vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 2 to 4094. Command Mode Interface

TL-SL5428E JetStream L2 Managed Switch CLI Guide 30 switchport general allowed vlan Description The switchport general allowed vlan command is used t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 31 Parameter vlan-id —— Specify IEEE 802.1Q VLAN ID, ranging from 1 to 4094. Command Mode Interface C

TL-SL5428E JetStream L2 Managed Switch CLI Guide 32 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the brief information

TL-SL5428E JetStream L2 Managed Switch CLI Guide 33 Chapter 4 MAC-based VLAN Commands MAC VLAN (Virtual Local Area Network) is the way to classify th

IV private-vlan primary...51 private-vlan

TL-SL5428E JetStream L2 Managed Switch CLI Guide 34 mac-vlan Description The mac-vlan command is used to enable a port for the MAC-based VLAN feat

TL-SL5428E JetStream L2 Managed Switch CLI Guide 35 Example Display the information of all the MAC-based VLAN entry: TL-SL5428E(config)#show mac-vlan

TL-SL5428E JetStream L2 Managed Switch CLI Guide 36 Chapter 5 Protocol-based VLAN Commands Protocol VLAN (Virtual Local Area Network) is the way to c

TL-SL5428E JetStream L2 Managed Switch CLI Guide 37 protocol-vlan vlan Description The protocol-vlan vlan command is used to create a Protocol-based

TL-SL5428E JetStream L2 Managed Switch CLI Guide 38 Syntax protocol-vlan no protocol-vlan Command Mode Interface Configuration Mode (interface fastE

TL-SL5428E JetStream L2 Managed Switch CLI Guide 39 Syntax show protocol-vlan vlan Command Mode Privileged EXEC Mode and Any Configuration Mode Exampl

TL-SL5428E JetStream L2 Managed Switch CLI Guide 40 Chapter 6 VLAN-VPN Commands VLAN-VPN (Virtual Private Network) function, the implement of a simpl

TL-SL5428E JetStream L2 Managed Switch CLI Guide 41 Parameter num —— The value of Global TPID. It must be 4 Hex integers. By default, it is 8100. Comm

TL-SL5428E JetStream L2 Managed Switch CLI Guide 42 switchport dot1q-tunnel mapping Description The switchport dot1q-tunnel mapping command is used to

TL-SL5428E JetStream L2 Managed Switch CLI Guide 43 Example Configure the Fast Ethernet port 3 as the VPN Up-link ports: TL-SL5428E(config)#interface

V Chapter 12 Binding Table Commands... 73 ip source binding ...

TL-SL5428E JetStream L2 Managed Switch CLI Guide 44 show dot1q-tunnel mapping interface Description The show dot1q-tunnel mapping interface command i

TL-SL5428E JetStream L2 Managed Switch CLI Guide 45 Chapter 7 Voice VLAN Commands Voice VLANs are configured specially for voice data stream. By conf

TL-SL5428E JetStream L2 Managed Switch CLI Guide 46 no voice vlan aging time Parameter time —— Aging time (in minutes) to be set for the Voice VLAN. I

TL-SL5428E JetStream L2 Managed Switch CLI Guide 47 voice vlan mac-address Description The voice vlan mac-address command is used to create Voice VLAN

TL-SL5428E JetStream L2 Managed Switch CLI Guide 48 Parameter manual | auto —— Port mode. Command Mode Interface Configuration Mode (interface fastEth

TL-SL5428E JetStream L2 Managed Switch CLI Guide 49 show voice vlan Description The show voice vlan command is used to display the global configura

TL-SL5428E JetStream L2 Managed Switch CLI Guide 50 show voice vlan switchport Description The show voice vlan switchport command is used to display t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 51 Chapter 8 Private VLAN Commands Private VLANs are configured specially for saving VLAN resource o

TL-SL5428E JetStream L2 Managed Switch CLI Guide 52 Command Mode VLAN Configuration Mode (VLAN) Example Configure the VLAN 4 as the community VLAN of

TL-SL5428E JetStream L2 Managed Switch CLI Guide 53 Syntax switchport private-vlan { promiscuous | host } no switchport private-vlan { promiscuous | h

VI ip dos-prevent detect...94 clear ip dos-

TL-SL5428E JetStream L2 Managed Switch CLI Guide 54 Example Configure host type Fast Ethernet port 3 as a member of primary VLAN 3 and secondary VLAN

TL-SL5428E JetStream L2 Managed Switch CLI Guide 55 show vlan private-vlan Description The show vlan private-vlan command is used to display the Priva

TL-SL5428E JetStream L2 Managed Switch CLI Guide 56 Chapter 9 GVRP Commands GVRP (GARP VLAN registration protocol) is an implementation of GARP (gene

TL-SL5428E JetStream L2 Managed Switch CLI Guide 57 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet /

TL-SL5428E JetStream L2 Managed Switch CLI Guide 58 gvrp timer Description The gvrp timer command is used to set a GVRP timer for the desired port. To

TL-SL5428E JetStream L2 Managed Switch CLI Guide 59 show gvrp global Description The show gvrp global command is used to display the global GVRP statu

TL-SL5428E JetStream L2 Managed Switch CLI Guide 60 Chapter 10 Etherchannel Commands Etherchannel Commands are used to configure LAG and LACP functio

TL-SL5428E JetStream L2 Managed Switch CLI Guide 61 port-channel load-balance Description The port-channel load-balance command is used to configure t

TL-SL5428E JetStream L2 Managed Switch CLI Guide 62 Command Mode Global Configuration Mode Example Configure the LACP system priority as 1024 globally

TL-SL5428E JetStream L2 Managed Switch CLI Guide 63 Parameter channel-group-num —— The EtherChannel Group number, ranging from 1 to 14. By default,

VII show logging flash... 115 Chapter 19

TL-SL5428E JetStream L2 Managed Switch CLI Guide 64 Parameter channel-group-num —— The EtherChannel Group number, ranging from 1 to 14. By default,

TL-SL5428E JetStream L2 Managed Switch CLI Guide 65 Chapter 11 User Manage Commands User Manage Commands are used to manage the user’s logging inform

TL-SL5428E JetStream L2 Managed Switch CLI Guide 66 TL-SL5428E(config)#user name tplink password password type admin status enable user access-contr

TL-SL5428E JetStream L2 Managed Switch CLI Guide 67 Syntax user access-control mac-based mac-addr no user access-control Parameter mac-addr —— The sou

TL-SL5428E JetStream L2 Managed Switch CLI Guide 68 TL-SL5428E(config)#user access-control port-based interface range fastEthernet 1/0/2-6 user max-n

TL-SL5428E JetStream L2 Managed Switch CLI Guide 69 Parameter minutes ——The timeout time, ranging from 5 to 30 in minutes. The value is 10 by default.

TL-SL5428E JetStream L2 Managed Switch CLI Guide 70 Enter the Virtual Terminal configuration mode so as to prepare further configurations such as pass

TL-SL5428E JetStream L2 Managed Switch CLI Guide 71 login Description The login command is used to configure the login of a switch not to use the user

TL-SL5428E JetStream L2 Managed Switch CLI Guide 72 Configure the login of Console port connection 0 as login local mode: TL-SL5428E(config)#line cons

TL-SL5428E JetStream L2 Managed Switch CLI Guide 73 Chapter 12 Binding Table Commands You can bind the IP address, MAC address, VLAN and the connecte

VIII ip address...138 ip add

TL-SL5428E JetStream L2 Managed Switch CLI Guide 74 Command Mode Global Configuration Mode Example Bind an ACL entry with the IP 192.168.0.1, MAC 00:0

TL-SL5428E JetStream L2 Managed Switch CLI Guide 75 Command Mode Global Configuration Mode Example Modify the hostname as “tp-link” of the entry with

TL-SL5428E JetStream L2 Managed Switch CLI Guide 76 Syntax ip dhcp snooping global { [global-rate global-rate] [dec-threshold dec-threshold] [dec-ra

TL-SL5428E JetStream L2 Managed Switch CLI Guide 77 no ip dhcp snooping information option Command Mode Global Configuration Mode Example Enable the O

TL-SL5428E JetStream L2 Managed Switch CLI Guide 78 ip dhcp snooping information remote-id Description The ip dhcp snooping information remote-id comm

TL-SL5428E JetStream L2 Managed Switch CLI Guide 79 Parameter string —— Enter the sub-option Circuit ID, which contains 32 characters at most. Comma

TL-SL5428E JetStream L2 Managed Switch CLI Guide 80 ip dhcp snooping mac-verify Description The ip dhcp snooping mac-verify command is used to enable

TL-SL5428E JetStream L2 Managed Switch CLI Guide 81 Command Mode Interface Configuration Mode (interface fastEthernet / interface range fastEthernet /

TL-SL5428E JetStream L2 Managed Switch CLI Guide 82 Command Mode Privileged EXEC Mode and Any Configuration Mode Example Display the IP-MAC-VID-PORT b

TL-SL5428E JetStream L2 Managed Switch CLI Guide 83 show ip dhcp snooping interface Description The show ip dhcp snooping interface command is used to